LEFROY EXPLORATION LIMITED — Capital/Financing Update 2017

Apr 2, 2017

==> picture [177 x 46] intentionally omitted <==

ASX Release: 3 April 2017

Exploration Update

New Gold Anomalies Defined in Lake Lefroy

Key Points:

• Aircore drilling identifies two new broad and cohesive gold anomalies in Lake Lefroy at the Lefroy Gold Project.

• The gold anomalies define a new mineralised geological trend over a 3.5km strike that is subparallel and to the east of the Woolibar Fault.

• Encouraging intersections returned from each anomaly, including 4m at 1.71g/t Au from 44m in LEFA 086 at target LLT04, and 4m at 2.39g/t from 88m in LEFA 113 at target LLT06

• Of the seven conceptual targets evaluated in the drill program, three have generated encouraging gold results and intersected promising geological attributes that support the need for further drilling

• Initial program evaluated only 6% of tenure held by the Company on Lake Lefroy

• New data acquired to be evaluated with the Companys previously acquired geophysical data to advance the geological model and provide additional drill targets

• Follow up drilling being planned and scheduled for early May.

The Board of Lefroy Exploration Limited (ASX: LEX) (“Lefroy” or “the Company”) is pleased to announce the receipt of final assay results from composite samples from its early stage Lake Lefroy aircore drilling program at its flagship Lefroy Gold Project (“LGP” or “Project”), located approximately 50km to the south east of Kalgoorlie. The results from this preliminary exploration program have reaffirmed the Company’s concept of the emerging gold prospectivity along or proximal to the Woolibar Fault.

Reflecting on the results of the lake drilling program Lefroy Exploration Limited Managing Director, Wade Johnson said “these are encouraging early results from a wide spaced and shallow drill program testing geophysical targets within the vast openness of Lake Lefroy. We are pleased to have delineated three gold anomalies that warrant further evaluation from our first phase of exploration and scheduling follow up drilling for May”.

Lefroy Exploration Australian Registered Office: Level 1 11 Ventnor Avenue ARBN 052 123 930 West Perth 6005 Australia Phone +61 08 9321 0984 Fax +61 08 9226 2636 Head Office: Email info@lefroyexploration.com Palm Grove House Roadtown Tortola British Virgin Islands

www.lefroyexploration.com

==> picture [178 x 46] intentionally omitted <==

The Company completed an early stage aircore drill program in February 2017 to evaluate seven priority target areas located within the eastern part of Lake Lefroy in its wholly owned tenements (Figure1). The seven targets evaluated comprised six conceptual targets defined from geophysical datasets and one geochemical target known as the Zanex Prospect, where previous drilling by Cyprus Gold Australia Limited in 1997 intersected 6m at 2.97gpt Au from wide spaced aircore drilling, that has never been followed up (refer to LEX Prospectus dated 8 September 2016).

==> picture [336 x 279] intentionally omitted <==

Figure 1 Lefroy Project tenement package, location of targets evaluated in Lake Lefroy and extent of geophysical interpretation shown in red outline (inset Figure 2)

The six conceptual targets (Figure 2) were generated following interpretation of airborne magnetic and ground gravity geophysical datasets that has provided an improved geological and structural framework for the area (refer LEX: ASX announcement 23 December 2016). These targets were selected on the basis of areas of geological and or structural complexity that have been derived from interpreting the geophysical data, and in particular the detailed ground gravity data, acquired by the Company in November 2016.

Assay results from composite samples (4m) have been received for the remaining 74 holes (LEFA 60-132) of the program. These results were from targets LLT03, 4,5,6,7 and also both infill and extensional drill holes from the Zanex Prospect.

The recent results have highlighted two new and emerging targets at LLT04 and LLT06 based upon a subtle geochemical gold signature, a favourable geological environment and trends defined from aeromagnetic data (Figure 3).

2

==> picture [178 x 46] intentionally omitted <==

Contouring maximum gold value in each hole has resulted in the definition of cohesive anomalies (+40ppb Au) at LTT4 and 6. Importantly, the best intersections returned from each anomaly were 4m at 1.71g/t Au from 44m in LEFA 086 at target LLT04 ( Figure 4), and 4m at 2.39g/t from 88m in LEFA 113 at target LTT06. Targets LLT4 and 6 are located 3.5km apart along strike on the same magnetic unit, which from bottom of hole drill chips is recognised to be a magnetite altered mafic unit. (Figure 3).

EXPLORATION PROGRAM DETAILS

All targets evaluated in the February program lie along or adjacent to a corridor termed the Woolibar Trend (Figure 2). Within Lake Lefroy, the targets extend over a 10km northwest strike length. To the north of Zanex, this trend encompasses the historical Cutters Luck gold workings and a series of small but nevertheless important alluvial gold workings. These occurrences support the hypothesis that the trend could be gold bearing.

The Woolibar corridor is part of the Company’s broader multi target exploration focus within the Lefroy Gold Project, where aircore drilling was recently commenced at the Lucky Strike prospect.

==> picture [386 x 352] intentionally omitted <==

Figure 2 Inset Map- Highlighting geological interpretation on left and TMI RTP aeromagnetic image on right, both with targets drilled, and extent of Lake Lefroy (refer to inset maps for Zanex and LTT4&6).

3

==> picture [178 x 46] intentionally omitted <==

Each of the target areas (Figure 2) were evaluated with wide spaced vertical air core drilling as an initial test to understand the geology beneath the recent lake sediments and older transported cover sequences. Drill traverses were spaced at either 160m or 320m apart, and hole centres mainly 80m apart but up to 160m. The methodology of the wide spaced program was to determine the depth of the cover and regolith, determine geology to support ongoing development of the geological model and to search for indicators (alteration, geochemistry) or low tenor gold anomalies that could represent the footprint of a primary ( fresh rock) gold system.

The exploration methodology and approach employed by the Company is derived from the key learnings from the discovery history of the Invincible gold deposit at St Ives in the western half of Lake Lefroy. The discovery of Invincible was concealed for many years due to the limited extent of its gold footprint in the regolith, and historical air core and RAB holes drilled within 20m of the deposit had no discernable gold anomaly (Woodcock, et al, 2015). There is no discernable regolith profile over Invincible, with younger lake sediments laying directly on oxidised bedrock (saprock) with little saprolite present, which is termed a stripped profile, and hence any well-developed regolith which could host a broad supergene anomaly was removed.

The Company has factored this aspect into its exploration and understanding of results from drilling in Lake Lefroy. The gold footprint of primary mineralisation in the regolith could be discrete and the gold values subtle. Hence, the company considers weak or subtle (less than 0.1g/t Au) gold response from wide spaced drilling in areas of poor regolith development could be represent deeper primary mineralisation.

A total of 4881m of drilling was completed in 92 holes over the seven targets in February 2017. Drill hole depths predominantly ranged from 30-55m, the air core drill technique terminating near or top of fresh rock. However at target LLT06 (Figure 2) holes terminated at depths of 80-108m encountering deeper transported cover above basement lithological units.

This phase of exploration has tested a number (two) of structural trends where previous exploration in the 1990s had found indications of gold mineralisation and that has now identified a new gold mineralised geological trend subparallel and to the east of the Woolibar Fault.

The gold results from targets LLT04 and LLT06 are of significance given the regolith environment interpreted from the drilling. The drilling intersected a variable thickness of firstly recent lake clays, secondly transported palaeochannel clays that unconformably overlay weathered basement rocks. The weathering profile is partially stripped that has resulted in the loss of the upper saprolite or the strongly oxidised portion of the profile where stronger concentrations of supergene gold could occur. Consequently the transported clays overlay lower saprolite and saprock, where the gold footprint from a primary source can be much smaller and the tenor of gold subtle. The Company is very encouraged by the results generated from the initial wide spaced drilling at LLT04 and LLT06 that has defined two new and emerging prospects that warrant further exploration.

4

==> picture [178 x 46] intentionally omitted <==

==> picture [321 x 292] intentionally omitted <==

Figure 3 Inset Map- Drill plan at showing the LTT4&6 targets over TMI - RTP1VD aeromagnetic image. Left image highlights the targeted break in the aeromagnetic trend.

==> picture [381 x 242] intentionally omitted <==

Figure 4 Drill Section at LTT4 target, highlighting transported cover, stripped regolith profile and key intersections from the wide spaced drilling.

5

==> picture [178 x 46] intentionally omitted <==

Results were also received for four infill and two strike extension drill traverses totaling six holes at Zanex. The aim of the ten additional holes was to follow up an encouraging intersection of 17m at 2.14g/t Au from 40m to the end of hole returned from hole LEFA 47 (Table 1) from the recent program. The hole intersected some 20m of transported cover above saprolite and terminated in an interpreted altered mafic lithology. Two infill holes at 40m centres were drilled next to LEFA 47 and results are pending and two holes 40m to the south. The best intersection returned from the 4m composite sampling was 4m at 0.16g/t Au from 48m in hole LEFA 128, located 40m to the west of LEFA 47. The Zanex Prospect consists of a north west trending sequence of strongly altered high Mg basalt over a 500m strike length intruded by porphyry. This early stage drilling remains predominantly wide spaced drilling within a stripped regolith profile. Exploration is underway to collect the 1m samples from selected holes for analysis to assist in improving the geochemical response.

ONGOING WORK PROGRAM

The Company is encouraged by the results of the initial exploration program over Lake Lefroy and further work is in progress. Bottom of hole (BoH) samples from drill holes that penetrated bedrock have been submitted for multielement analysis ( suite of elements) and will be used to map geochemical patterns from pathfinder elements (e.g. Arsenic, Tellurium, Bismuth) that could be associated with a primary gold system. Advancing the geological model is integral to the ongoing work program and will involve incorporating the new geological knowledge from drilling to further interrogate the geophysical data, to deliver an updated geological interpretation and generate new drill targets. Follow up drilling is being planned for May.

==> picture [355 x 267] intentionally omitted <==

Figure 5 Looking south west over Lake Lefroy toward St Ives with drill rig in background sited on last hole of the program LEFA 132 ( Zanex)

6

==> picture [178 x 46] intentionally omitted <==

About Lefroy Exploration and the Lefroy Project

Lefroy Exploration Limited is a new WA based and focused explorer taking a disciplined methodical approach in the search for high value gold and nickel deposits. Key Projects include the Lefroy Gold Project (LGP) to the south east of Kalgoorlie and the Lake Johnston Project 120km to the west of Norseman.

The 100% owned Lefroy Gold Project contains mainly granted tenure covering 547km[2] , located in the heart of the world class gold production area between Kalgoorlie and Norseman. The Project is in close proximity to Gold Fields’ St Ives gold camp, which contains the newly discovered Invincible gold mine located in Lake Lefroy, and is also immediately south of Silver Lake Resources (ASX: SLR) Daisy Milano gold mining operation. The LGP supports the commitment by the Company to focus on exploration for new greenfields gold discovery’s in areas of limited or no previous exploration but in areas that have favourable geological and geophysical characteristics.

==> picture [386 x 326] intentionally omitted <==

Location of the Lefroy Gold Project relative to Kalgoorlie, Gold Fields St Ives Gold Camp near Lake Lefroy, and major gold deposits .

For Further Information please contact: Wade Johnson Telephone: +61 8 93210984 Email: wjohnson@lefroyex.com

7

==> picture [178 x 46] intentionally omitted <==

Table 1 2017 AirCore Drilling-Lefroy Gold Project-Woolibar Trend

Drill hole intersections tabulated below are calculated with a 0.04g/t Au lower cut for the entire drill program. Samples are routinely collected as 4m composite intervals. The last sample of each hole is dedicated 1m interval, and the prior sample can vary from 1-4m depending on final depth. Only significant (>0.04ppm Au) intersections are shown.

Hole Id	Collar N (MGA)	Collar E ( MGA)	Collar RL	Dip ˚	Azimuth ˚	Hole Depth (m)	Depth From (m)	Depth To (m)	Gold Intersection (downhole width)	Au Value (g/t)
LEFA044	6551961	384739	285	-90	0	44	36	40	4	0.04
LEFA047	6551962	384898	285	-90	0	57	8	12	4	0.04
LEFA047	6551962	384898	285	-90	0	57	16	20	4	0.08
LEFA047	6551962	384898	285	-90	0	57	40	44	4	0.39
LEFA047	6551962	384898	285	-90	0	57	44	48	4	5.48
LEFA047	6551962	384898	285	-90	0	57	48	52	4	2.47
LEFA047	6551962	384898	285	-90	0	57	52	56	4	0.29
LEFA047	6551962	384898	285	-90	0	57	56	57	1	1.87
LEFA049	6551918	384994	285	-90	0	56	36	40	4	0.05
LEFA051	6551927	384850	285	-90	0	54	44	48	4	0.06
LEFA054	6551801	385020	285	-90	0	63	44	48	4	0.04
LEFA054	6551801	385020	285	-90	0	63	48	52	4	0.04
LEFA056	6551800	384861	285	-90	0	58	40	44	4	0.04
LEFA057	6551800	384783	285	-90	0	59	44	48	4	0.05
LEFA058	6551641	384757	285	-90	0	62	40	44	4	0.05
LEFA058	6551641	384757	285	-90	0	62	44	48	4	0.04
LEFA062	6552002	385601	285	-90	0	56	8	12	4	0.05
LEFA062	6552002	385601	285	-90	0	56	55	56	1	0.04
LEFA063	6552004	385762	285	-90	0	51	0	4	4	0.05
LEFA064	6552002	385916	285	-90	0	45	4	8	4	0.04
LEFA067	6552321	386000	285	-90	0	49	32	36	4	0.04
LEFA069	6552318	385683	285	-90	0	56	55	56	1	0.27
LEFA076	6553317	385181	285	-90	0	47	32	36	4	0.21
LEFA077	6553320	385339	285	-90	0	48	4	8	4	0.04
LEFA086	6550856	390854	285	-90	0	73	28	32	4	0.12
LEFA086	6550856	390854	285	-90	0	73	44	48	4	1.71
LEFA086	6550856	390854	285	-90	0	73	72	73	1	0.15
LEFA092	6550229	390678	285	-90	0	34	24	28	4	0.04
LEFA093	6550231	390517	285	-90	0	74	32	36	4	0.04
LEFA095	6550232	390439	285	-90	0	55	32	36	4	0.06
LEFA105	6547602	389607	285	-90	0	47	44	46	2	0.04
LEFA109	6547959	392655	285	-90	0	73	48	52	4	0.1
LEFA110	6547957	392980	285	-90	0	52	20	24	4	0.06

8

==> picture [178 x 46] intentionally omitted <==

Hole Id	Collar N (MGA)	Collar E ( MGA)	Collar RL	Dip ˚	Azimuth ˚	Hole Depth (m)	Depth From (m)	Depth To (m)	Gold Intersection (downhole width)	Au Value (g/t)
LEFA112	6546998	392519	285	-90	0	85	20	24	4	0.07
LEFA113	6546997	392838	285	-90	0	108	88	92	4	2.39
LEFA114	6547001	393160	285	-90	0	91	84	88	4	0.23
LEFA116	6547320	393279	285	-90	0	61	20	24	4	0.08
LEFA116	6547320	393279	285	-90	0	61	24	28	4	0.04
LEFA117	6547321	392960	285	-90	0	87	20	24	4	0.06
LEFA117	6547321	392960	285	-90	0	87	80	84	4	0.04
LEFA117	6547321	392960	285	-90	0	87	84	86	2	0.05
LEFA117	6547321	392960	285	-90	0	87	86	87	1	0.07
LEFA119	6547639	392327	285	-90	0	82	60	64	4	0.08
LEFA121	6547647	392965	285	-90	0	103	60	64	4	0.05
LEFA124	6551481	384901	285	-90	0	65	48	52	4	0.04
LEFA124	6551481	384901	285	-90	0	65	52	56	4	0.05
LEFA128	6551961	384863	285	-90	0	55	0	4	4	0.08
LEFA128	6551961	384863	285	-90	0	55	48	52	4	0.16
LEFA128	6551961	384863	285	-90	0	55	52	54	2	0.06

Notes Specific-ASX Announcements

The following announcements were lodged with the ASX and further details (including supporting JORC Reporting Tables) for each of the sections noted in this Announcement can be found in the following releases. Note that these announcements are not the only announcements released to the ASX but specific to exploration reporting on the Lefroy Gold Project.

• Lefroy Exploration Limited-Prospectus 8 September 2016

• Lefroy Commences Exploration 24 October 2016

• Gravity Survey Completed at Lefroy Project 22 November 2016

• Managing Directors AGM Presentation 5 December 2016

• Exploration Update 23 December 2016

• Drilling Campaign Commences on Lake Lefroy 8 February 2017

• Initial Drilling at Lake Lefroy Completed 9 March 2017

The information in this announcement that relates to exploration targets and exploration results is based on information compiled by Wade Johnson a competent person who is a member of the Australian Institute of Geoscientists (AIG). Wade Johnson is employed by Lefroy Exploration Limited. Wade has sufficient experience that is relevant to the style of mineralisation and type of deposits under consideration and to the activity being undertaken to qualify as a Competent Person as defined in the 2012 edition of the JORC Code. Wade Johnson consents to the inclusion in this announcement of the matters based on his work in the form and context in which it appears.

Reference

Woodcock, J., Edmonds, P., Moore, S., Doutch, D., Foley, A., 2015. St Ives gold mine; Invincible: From Discovery to development. In NewGenGold 2015 Conference Proceedings.

9

JORC CODE, 2012 Edition-Table 1 Report –Lefroy Project –Woolibar Trend-as at 3 April 2017 SECTION 1: SAMPLING TECHNIQUES AND DATA

SECTION1:	SAMPLING TECHNIQUES AND DATA
Criteria	JORC Code Explanation	Commentary
Sampling techniques	• Nature and quality of sampling (eg cut channels, random chips, or specific specialised industry standard measurement tools appropriate to the minerals under investigation, such as down hole gamma sondes, or handheld XRF instruments, etc). These examples should not be taken as limiting the broad meaning of sampling. • Include reference to measures taken to ensure sample representivity and the appropriate calibration of any measurement tools or systems used. • Aspects of the determination of mineralisation that are Material to the Public Report. In cases where ‘industry standard’ work has been done this would be relatively simple (eg ‘reverse circulation drilling was used to obtain 1 m samples from which 3 kg was pulverised to produce a 30 g charge for fire assay’). In other cases more explanation may be required, such as where there is coarse gold that has inherent sampling problems. Unusual commodities or mineralisation types (eg submarine nodules) may warrant disclosure of detailed information.	• The sampling noted in this release has been carried out using AirCore (AC) drilling at several targets located in Lake Lefroy, along a corridor termed the Woolibar Trend. The AC program comprised 92 vertical holes for 4881m, holes varying in depth from 3-108m with an average depth of 53m. At each target hole spacing was primarily at 160m centres on traverses located 160m to 320m apart. At some targets (eg Zanex) the hole spacing was bought down to a regular 80m grid • Sampling and QAQC protocols as per industry best practice with further details below. • AC samples were collected from the cyclone at 1m intervals and laid out in rows of 10 or 20m (10-20 samples) on the ground (salt lake) or contained in green plastic bags. If laid out on the ground 1m library samples were collected in calico sample bags for future detailed sampling if required. Composite 4m samples were then collected by scoop or grab sampling the 1m piles with a flour scoop to produce a bulk 2-3kg sample which was sent to the Laboratory in Kalgoorlie for analysis. Samples were dried, pulverised, split to produce a 40g sample for analysis by fire assay with Au determination by Atomic Absorption Spectrometry.
Drilling techniques	• Drill type (eg core, reverse circulation, open-hole hammer, rotary air blast, auger, Bangka, sonic, etc) and details (eg core diameter, triple or standard tube, depth of diamond tails, face-sampling bit or other type, whether core is oriented and if so, by what method, etc).	• The AirCore (AC) drilling was completed by Raglan Drilling (Kalgoorlie). The AC drill bit has a diameter of 78mm and collects samples through an inner tube to reduce contamination, but also allows better penetration through any palaeochannel puggy clays and fine sands. Aircore drilling is blade refusal and hence terminates in fresh rock or hard material such asquartz.
Drill sample recovery	• Method of recording and assessing core and chip sample recoveries and results assessed. • Measures taken to maximise sample recovery and ensure representative nature of the samples. • Whether a relationship exists between sample recovery and grade and whether sample bias may have occurred due to preferential loss/gain of fine/coarse material.	• The majority of the samples collected from the AC drill program were moist. Given all the drilling was in Lake Lefroy the initial 0-20m of drilling was wet with muddy samples, some with poor recovery. Minor AC samples were wet at the base of the holes. Sample recovery below the base of alluvium (BOA) was considered appropriate with some samples dry with good sample recovery. • Sample recovery size and sample condition (dry, wet, moist) recorded. Recovery of samples estimated to be 10- 100%, with limited recovery particularly drilling through the surficial lake clays and puggy moist transported clays. • Drilling with care (eg. clearing hole at start of rod, regular cyclone cleaning) if water encountered to reduce incidence of wet – sticky sample and cross contamination. • Insufficient sample population to determine whether relationship exists between sample recovery and grade. The quality of the sample (wet, dry, low recovery)was recorded duringlogging.

Criteria	JORC Code Explanation	Commentary
Logging	• Whether core and chip samples have been geologically and geotechnically logged to a level of detail to support appropriate Mineral Resource estimation, mining studies and metallurgical studies. • Whether logging is qualitative or quantitative in nature. Core (or costean, channel, etc) photography. • The total length and percentage of the relevant intersections logged.	• Detailed logging of drill chips to record, regolith, lithology, structure, mineralisation and recoveries in each hole by an experienced geologist. • Logging carried out by sieving 2m composite sample cuttings, washing in water and the entire hole collected in plastic chip trays for future reference. • Every hole was logged for the entire length.
Sub-sampling techniques and sample preparation	• If core, whether cut or sawn and whether quarter, half or all core taken. • If non-core, whether riffled, tube sampled, rotary split, etc and whether sampled wet or dry. • For all sample types, the nature, quality and appropriateness of the sample preparation technique. • Quality control procedures adopted for all sub-sampling stages to maximise representivity of samples. • Measures taken to ensure that the sampling is representative of the in situ material collected, including for instance results for field duplicate/second-half sampling. • Whether sample sizes are appropriate to the grain size of the material being sampled.	• No core drilling completed • Composite samples of 4m were collected by scoop or grab (sticky clays) sampling 1m intervals into pre-numbered calico bags. Sample weight 2 - 3 kg. The last interval of each hole was a specific 1m. Collected 4m Samples placed in plastic and/or polyweave bags for despatch to assay laboratory. • The sample preparation of the AC follows industry best practice, involving oven drying, pulverising, to produce a homogenous sub sample for analysis. • Along with composite samples, standards and blanks were randomly inserted (approximately every 40 samples) and were included in the laboratory analysis. Standards were certified reference material prepared by Geostats Pty Ltd. Duplicate samples were collected at zones of interest and at irregular intervals of about 1 in everythree holes.
Quality of assay data and laboratory tests	• The nature, quality and appropriateness of the assaying and laboratory procedures used and whether the technique is considered partial or total. • For geophysical tools, spectrometers, handheld XRF instruments, etc, the parameters used in determining the analysis including instrument make and model, reading times, calibrations factors applied and their derivation, etc. • Nature of quality control procedures adopted (eg standards, blanks, duplicates, external laboratory checks) and whether acceptable levels of accuracy (ie lack of bias) and precision have been established.	• Samples routinely analysed for gold using the 40gram Fire Assay digest method with an AAS finish at Bureau Veritas’s Kalgoorlie Laboratory. A Bottom of Hole (BOH) sample was also collected but is yet to be analysed. This sample was carefully selected and collected by the geologist to represent near fresh (Saprock) rock at the base of the hole and will be analysed for a suite of elements. • No geophysical tools, spectrometers or hand held XRF instruments used. • Quality control process and internal laboratory checks demonstrate acceptable levels of accuracy. At the laboratory, regular assay repeats, lab standards, checks and blanks are analysed.

Criteria	JORC Code Explanation	Commentary
Verification of sampling and assaying	• The verification of significant intersections by either independent or alternative company personnel. • The use of twinned holes. • Documentation of primary data, data entry procedures, data verification, data storage (physical and electronic) protocols. • Discuss any adjustment to assay data.	• The results have been reviewed and checked by alternative company personnel. • LEFA 050 twinned historical drill hole LFA182 drilled by Cyprus Gold Australia Limited in 1996. • Capture of field logging is electronic using Toughbook hardware and Logchief software. Logged data is then exported as an excel spreadsheet to the Companys external database managers which will be loaded to the Company’s DATASHED database and validation checks completed to ensure data accuracy. Assay files are received electronically from the laboratory by the Managing Director and filed to the companys server, and provided to the external database manager. • There has been no adjustment to the assay data. The primary Au field reported by the laboratory is the value used for plotting, interrogating and reporting.
Location of data points	• Accuracy and quality of surveys used to locate drill holes (collar and down-hole surveys), trenches, mine workings and other locations used in Mineral Resource estimation. • Specification of the grid system used. • Quality and adequacy of topographic control.	• Drill hole positions were surveyed using a hand-held Garmin GPS with a horizontal (Easting Northing) accuracy of +-5m. Drill location is set up by the supervising geologist. No downhole surveys completed. • Grid System – MGA94 Zone 51. • Topographic elevation captured by using reading from Garmin hand held GPS with an accuracy of+-10m and considered suitable for the flat terrain.
Data spacing and distribution	• Data spacing for reporting of Exploration Results. • Whether the data spacing and distribution is sufficient to establish the degree of geological and grade continuity appropriate for the Mineral Resource and Ore Reserve estimation procedure(s) and classifications applied. • Whether sample compositing has been applied.	• Hole spacing at nominal 80m or 160m centres on new east west orientated drill lines with line spacing’s varying from 160m to 320m. Infill drilling (4 holes) to 40m centres at the Zanex Prospect on existing sections. • AC samples composite range 2-4m but generally 4m. No assay compositing has been applied.
Orientation of data in relation to geological structure	• Whether the orientation of sampling achieves unbiased sampling of possible structures and the extent to which this is known, considering the deposit type. • If the relationship between the drilling orientation and the orientation of key mineralised structures is considered to have introduced a sampling bias, this should be assessed and reported if material.	• The East West orientated drill traverses considered effective to evaluate the northerly-north westerly trending geology and interpreted regional Woolibar Fault which has been interpreted from aeromagnetic and gravity data. Drill holes are reconnaissance and are orientated appropriately to ensure unbiased sampling of the geological trends • The AC drilling is reconnaissance in nature, being wide spaced and the orientation of the deformed rocks intersected is yet to be confirmed.
Sample security	• The measures taken to ensure sample security.	• Individual composite samples were bagged in polyweave bags, collected and personally delivered to the Bureau Veritas Laboratory in Kalgoorlie by the Field Supervisor. Samples were sorted and checked for inconsistencies against submission sheet by Bureau Veritas staff at the Kalgoorlie laboratory. • Bureau Veritas check the samples received against the LEX submission form to notify

Criteria	JORC Code Explanation	Commentary
		of any missing or extra samples. Following analysis, the sample pulps and residues are retained by the laboratory in a secure storageyard.
Audits or reviews	• The results of any audits or reviews of sampling techniques and data.	• All results of this drill program were reviewed by the Senior Exploration Geologist and Managing Director. Anomalous gold intersections checked against library chip trays to correlate with geology. No specific site audits or reviews have been conducted.

Section 2: REPORTING OF EXPLORATION RESULTS – LEFROY PROJECT-Woolibar Trend as at 3 April 2017

Criteria	JORC Code Explanation	Commentary
Mineral tenement and land tenure status	• Type, reference name/number, location and ownership including agreements or material issues with third parties such as joint ventures, partnerships, overriding royalties, native title interests, historical sites, wilderness or national park and environmental settings. • The security of the tenure held at the time of reporting along with any known impediments to obtaining a licence to operate in the area.	• The Lefroy Project is located approximately 50 km in south east from Kalgoorlie, Western Australia and consists of a contiguous package of wholly owned tenements held under title by LEX or its wholly owned subsidiary’s Hogans Resources Pty Ltd. The work described in this report was undertaken on Prospecting leases P26/3889, P26/3890 and Exploration Licences 15/1447 & E26/184 held 100% by Lefroy Exploration Limited. • The tenements are current and in good standing with the Department of Mines and Petroleum(DMP)of Western Australia.
Exploration done by other parties	• Acknowledgment and appraisal of exploration by other parties.	• Within Lake Lefroy and along the interpreted Woolibar Trend the key exploration in the area now known as Zanex was completed Cyprus Gold Australia Corporation in 1997 and this drill program is well documented in a report to the Department of Mines and Petroleum WAMEX report A52840. This report clearly documents the air core drill program that resulted in the intersection in hole LFA182 drilled by Cyprus Gold Australia Limited. At the LLT 04 target prior drilling was completed by North Limited in 1996 and is documented in WAMEX report a48593. These holes are depicted on Figure 3.
Geology	• Deposit type, geological setting and style of mineralisation.	• The Lefroy Project is located in the southern part of the Norseman Wiluna Greenstone Belt and straddles the triple junction of three crustal units, the Parker, Boorara and Bulong Domain. The Lefroy project tenements are mostly covered by alluvial, colluvial and lacustrine material with very little outcrop. The project is underlain by a folded and fault bounded sequence of Archaean rocks, and in the Woolibar trend within Lake Lefroy area being predominantly metasediments, High Mg basalt and basalt. The key structural element is the interpreted North West trendingWoolibar Fault.
Drill hole Information	• A summary of all information material to the understanding of the exploration results including a tabulation of the following information for all Material drill holes: • easting and northing of the drill hole collar • elevation or RL (Reduced Level – elevation above	• Table containing drill hole collar, survey, and intersection data for material (gold intersections >0.04gpt Au) drill holes are included in the Table in the body of the announcement. • No Information has been excluded.

Criteria	JORC Code Explanation	Commentary
	sea level in metres) of the drill hole collar • dip and azimuth of the hole • down hole length and interception depth • hole length. • If the exclusion of this information is justified on the basis that the information is not Material and this exclusion does not detract from the understanding of the report, the Competent Person should clearly explain why this is the case.	• There are historical drill holes within the Zanex Prospect and these are depicted on the drill hole plan and section in the announcement. These holes were drilled by Cyprus Gold Australia Corporation in the mid 1990’s. • There are historical holes at the LLT04 target drilled by North Limited in 1996, the location depicted on Figure 3 in the body of the announcement.
Data aggregation methods	• In reporting Exploration Results, weighting averaging techniques, maximum and/or minimum grade truncations (eg cutting of high grades) and cut-off grades are usually Material and should be stated. • Where aggregate intercepts incorporate short lengths of high grade results and longer lengths of low grade results, the procedure used for such aggregation should be stated and some typical examples of such aggregations should be shown in detail. • The assumptions used for any reporting of metal equivalent values should be clearly stated.	• There is no weighting or averaging of the reported grades. High grades have not been cut. A lower cut off of 0.04gpt Au has been used to identify significant results in Table 1. These are considered significant given the first pass reconnaissance nature of the drilling. • Where present, higher grade values are included in the intercepts table and assay values equal to or > 1.0 g/t Au. • No metal equivalent values or formulas used.
Relationship between mineralisation widths and intercept lengths	• These relationships are particularly important in the reporting of Exploration Results. • If the geometry of the mineralisation with respect to the drill hole angle is known, its nature should be reported. • If it is not known and only the down hole lengths are reported, there should be a clear statement to this effect(eg ‘down hole length, true width not known’).	• All results are based on down-hole metres. • Given the wide spaced reconnaissance nature of the drilling the geometry of the mineralisation reported is not sufficiently known and the true width is not known
Diagrams	• Appropriate maps and sections (with scales) and tabulations of intercepts should be included for any significant discovery being reported. These should include, but not be limited to a plan view of drill hole collar locations and appropriate sectional views.	• Appropriate summary diagrams (section & plan) are included in the accompanying announcement.
Balanced reporting	• Where comprehensive reporting of all Exploration Results is not practicable, representative reporting of both low and high grades and/or widths should be practiced to avoid misleading reporting of Exploration Results.	• Significant assay results are provided in Table 1 for the entire LEX drill program. • Drill holes with no significant results are not reported. • Significant assay results from historical drilling are noted in the body of the report (Zanex)and depicted on Figure 3.
Other substantive exploration data	• Other exploration data, if meaningful and material, should be reported including (but not limited to): geological observations; geophysical survey results; geochemical survey results; bulk samples – size and method of treatment; metallurgical test results; bulk density, groundwater, geotechnical and rock characteristics; potential deleterious or contaminating substances.	• All relevant data has been included within this report.
Further work	• The nature and scale of planned further work (eg tests for lateral extensions or depth extensions or large-scale step-out drilling). • Diagrams clearly highlighting the areas of possible extensions, including the main geological interpretations and future drilling areas, provided this information is not commercially sensitive.	• The next stage of exploration will involve collection of 1m re samples from drill holes, updating the geological model and planning further air core drilling.